ARCHIVED FORUM -- March 2012 to February 2022READ ONLY FORUM
This is the second Archived Forum which was active between 1st March 2012 and 23rd February 2022
Hi I do have a Avant 32 with a Beosound 9000 in the same room and a Beolab 3500 in another. We have token away the Avant 32. Since the Beolab 3500 works only for seconds. First I saw TV Operated on the Beosound but this now out. What can be the problem? I have tried the A Option but still not OK. Thanks for your help ...
Thanks for your answer. The Beosound is on A. Option 1 yet. Do I also have to set it on the Beolab 3500? Yesterday when pushing on the Timer button ON/OFF it shows TV OPERATED Now it doesn't show it anymore .... Strange situation
Thanks Stan. Unfortunately still the same situation. Plays 5 seconds and done .....
You did not mention any Beolabs connected to BS9000. If there are no eolabs connected, your BS "thinks", it is connected to a videomaster, which was the case before, an will automatically switch to A.OPT 0. A dummy plug might help. A DIN plug (7 or 5 pins) with a bridge soldered between pin 4 and pin 2. See also Beotech site.
Stefan
Hi Stefan. I have just tried with a dummy Masterlink plug but still working for some seconds. Due to works in our home the Beosound 9000 stands alone in 1 room with only the Beolab 3500 in another room. Must I change maybe the A option before taking away the Avant 32"?
You need a Powerlink dummy plug, not a Masterlink...
When the dummy is connected to a Powerlink socket, connect your BS to the mains and set it to A.OPT 1.
A short flash of the standby led should confirm option setting. Now it should be possible to control your BS via IR (Beo4, Beo6...).
Set your BL3000 to L.OPT 5 - watch the led confirmation)
Before you do this, I recommend to disconnect the "whole" system from the mains for some minutes - are you sure about pin code?
Hope this helps.
NO Still not. I put a Powerlink cable in the Beosound 9000. 220v of on the 2 B&O. Connect again 220v and A Option1 on the 9000 and L option5 on the 3500. Sometimes it stops after 5 seconds, sometimes after 45 sec. When stopped hold the radio button or for a while and it plays again ..... But after sometimes even this isn't working anymore.
I add a Beolab 6000 on the dummy cable and still the same. It plays in the mean room with BS9000 but the BL3500 stops again after some seconds. Could it be I had to put first the A Option1 before disconnecting the Avant32? Geert
AUTOCENTRALE: NO Still not. I put a Powerlink cable in the Beosound 9000. 220v of on the 2 B&O. Connect again 220v and A Option1 on the 9000 and L option5 on the 3500.
NO Still not. I put a Powerlink cable in the Beosound 9000. 220v of on the 2 B&O. Connect again 220v and A Option1 on the 9000 and L option5 on the 3500.
A Powerlink cable is NOT a dummy plug. Please reread my post above.
AUTOCENTRALE: Sometimes it stops after 5 seconds, sometimes after 45 sec. When stopped hold the radio button or for a while and it plays again ..... But after sometimes even this isn't working anymore.
Sometimes it stops after 5 seconds, sometimes after 45 sec. When stopped hold the radio button or for a while and it plays again ..... But after sometimes even this isn't working anymore.
What do you mean by "not working anymore"?
AUTOCENTRALE: I add a Beolab 6000 on the dummy cable and still the same. It plays in the mean room with BS9000 but the BL3500 stops again after some seconds. Could it be I had to put first the A Option1 before disconnecting the Avant32? Geert
Now you have a dummy plug (by connecting a BL) and it`s not the same. It`s working in the main room.
So the fault is on your BL3500 or the ML cable.
Try to disconnect your BS from ML (but keep connection to BL6000). Works?
By "not working anymore" I mean when the BL3500 stops, I push the radio button on the remote and it starts again for some seconds. After 4/5 times repeating the BL3500 doesn't react anymore. Geert
Hi Stefan I disconnected again from the main 220V lead and reconnect. A MIRACLE It works. After trying so many times suddenly it operates again. Thanks a lot for your help and time (patience). Regards, Gerard